Graphene Heated Pet Bed Bolster Dog Cat Bed USB Controller 3 Heat Levels 2H 4H 6H Timer Chew-Proof Steel Cord Washable Cover OEM ODM

A heated pet bed built as one article, not a pad under a bed: a bolster-walled pet bed whose sleeping surface is the heating element — a printed graphene film under a scratch-resistant denim face — driven by an in-line USB controller with HIGH / MED / LOW levels and a 2H / 4H / 6H self-ending timer, and wrapped in a chew-resistant steel spiral cord.

OEM / ODM. Low MOQ, factory direct. Denim blue is the reference colourway; the configurable surface is laid out below.

Four Layers, One Body

The artwork's layer diagram (detail sheet 3) stacks the bed top to bottom:

1. Scratch-resistant denim fabric — sleep surface and bolster walls
2. Graphene heating element — printed film, honeycomb pattern
3. High-density elastic cushion — the comfort core
4. Non-slip waterproof base — dotted underside, gripping hard floors

Because the element sits directly beneath the sleep surface, heat reaches the animal without crossing a padded shell. The bolster rim is specified as high-density and supportive, so the wall holds a leaning cat instead of collapsing.

Controls: Three Levels, a Timer, a Constant Mode

The in-line controller carries two buttons and two indicator columns. One column steps through HIGH, MED, LOW. The other sets the timer — 2H, 4H or 6H — after which the bed switches itself off. A detail sheet adds a Constant position for uninterrupted warmth.

The cord terminates in a USB-A plug. The artwork prints no voltage figure alongside its low-voltage safe operation wording, and this listing borrows nothing: electrical values are written into the confirmed order.

The Cord, Built for Teeth

The safety sheet reads like a chew-test protocol, because it is one:

• Chew-resistant steel spiral cord — metal coils over the cable
• Waterproof insulated junction — sealed cord-to-bed joint
• Anti-pull strain relief — reinforced exit tail
• Flame-retardant wiring / short-circuit protection / bend-proof junction
• Pet-safe materials — eco-friendly and pet approved
• Overheat protection — built into the heating system

No claim here needs upgrading; the sheet already states the construction a buyer should verify on the sample.

Denim Shell, Washable Cover, Dotted Base

The shell is a denim-look woven polyester, listed as scratch-resistant, with an ergonomic bolster rim. The cover unzips and is removable and washable — the artwork shows the separated cover and body. The base is dotted and specified as a waterproof layer in the stack diagram. The element and controller are not the washable parts, and care guidance beyond the artwork follows the approved sample.

Size, Colourways, Patch

Blanks the Sheet Leaves to the Order

The sheet publishes no bed dimensions, no voltage figure, no wattage, no temperature range, no MOQ number and no certification marks — and this listing does not import them from other models. The artwork carries its own standing line: all dimensions and specifications are subject to final confirmed order. Each blank is filled at sample approval, in writing.

Built Around Your Brand Programme

• Leather patch — rectangle, paw, dog head or house shape; embossed, debossed or printed with your logo
• Dimensions — the L cut shown, or a custom size
• Fabric and colour — denim, grey and khaki shown; schemes per programme
• Controller and packaging — custom pod, retail box, labels and manuals
• MOQ — stated as low MOQ, factory direct; the number is quoted against the specification

Send the bed brief through our contact page — the blanks above become lines in the order specification.

Safety Notes for Heated Pet Beds

• Not for pets that cannot leave the bed unaided, or for animals recovering under veterinary care without owner supervision
• Use a timer position for unattended sessions; inspect the cord regularly in chewing-prone households
• Keep the bed and its USB source dry; layer-level water protection is claimed only as drawn (junction, base)
• Unplug before removing the cover for cleaning

Pet Bed Programme FAQ

What are the bed's dimensions in L?

Not printed in the reference set — cut dimensions are confirmed per order, and custom sizes are quotable.

What voltage does it run at?

The artwork states low-voltage safe operation without a figure; the value is written into the order specification.

What is the price?

USD23.9-30 per unit, with the final figure following the confirmed configuration.

Is the heating element removable for washing?

No — the cover unzips and washes; the element stays in the body.

Can we brand the bed?

Yes — leather patch, fabric colours, controller, packaging and labelling are part of the OEM/ODM programme.

This product is a comfort product and is not a medical device. It is not intended to diagnose, treat or prevent any disease, and it makes no claim about joints, muscles, circulation or any other condition. The glowing honeycomb pattern in the artwork is a heating illustration, not a thermal image. All dimensions and specifications are subject to final confirmed order; no voltage, wattage, temperature or MOQ figures are published in this listing, and certification status is confirmed per order. Layer-level water protection is claimed only as printed on the artwork.